HP Compaq 6530s Maintenance And Service Manual Maintenance and service manual (161 pages) HP Compaq NC4010 Frequently Asked Questions Manual Software update (6 pages) HP Compaq Presario,Presario 1030 Supplementary Manual Supplementary manual (4 pages).

• HP Compaq 6530s Notebook PC HP Compaq 6531s Notebook PC HP Compaq 6535s Notebook PC Display Replacement Guide. • Corporation. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.

Nothing herein should be construed as constituting an additional warranty. • Safety warning notice WARNING!

To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Canon Mg2470 Software Resetter on this page. Use the computer only on a hard, flat surface.

Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. • Safety warning notice ENWW. • Table of contents 1 Removal and replacement procedures Preliminary replacement requirements...2 Tools required...2 Service considerations...2 Plastic parts...2 Cables and connectors..3 Drive handling... 3 Grounding guidelines...4 Equipment guidelines..4 Component replacement procedures...

• Removal and replacement procedures ENWW. • Preliminary replacement requirements Tools required You will need the following tools to complete the removal and replacement procedures: ● Flat-bladed screwdriver ● Magnetic screwdriver ● Phillips P0 and P1 screwdrivers ● Torx T8 screwdriver Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures. • Cables and connectors CAUTION: When servicing the computer, be sure that cables are placed in their proper locations during the reassembly process. Improper cable placement can damage the computer. Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the cables during removal and insertion.

• Grounding guidelines Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ● When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times. • 493154-001 14.1-inch, WXGA display assembly with camera 493152-001 14.1-inch, WXGA display assembly 493151-001 For use only with HP Compaq 6530s and 6531s Notebook PC models 14.1-inch, WXGA BrightView display assembly with camera 491643-001 14.1-inch, WXGA display assembly with camera 491642-001 14.1-inch, WXGA BrightView display assembly. • Remove the battery (2) from the computer.

Remove the following screws: (1) Two slotted Torx ST8M2. Cara Install Windows Xp Di Hp Pavilion Dm1. 5×7.0 screws (2) Two Torx T8M2.0×2.0 broadhead (9-mm) screws Chapter 1 Removal and replacement procedures ENWW. • Remove the two slotted Torx ST8M2.5×7.0 screws that secure the keyboard to the computer. Turn the computer display-side up, with the front toward you. Open the computer as far as possible. Lift the switch cover (1) straight up until it disengages from the computer, and slide it back (2) until it rests on the display assembly. • Release the zero insertion force (ZIF) connector to which the LED board cable is attached, disconnect the LED board cable from the system board (1), and lift the switch cover up to remove it (2) from the system board. To disengage the four tabs (1) on the back of the keyboard from the switch cover, lift up the rear edge of the keyboard (2), and slide it back (3).

• Release the swinging ZIF connector (1) to which the keyboard cable is attached, and disconnect the keyboard cable (2) from the system board. Remove the keyboard. Turn the switch cover over. Remove the two Phillips PM2.0×2.0 broadhead screws (1) from the switch cover. Remove the LED power button board (2) from the switch cover.

• Remove the speakers (3) from the top cover. Turn the computer right-side up, with the front toward you. Open the computer as far as possible.

Disconnect the display panel cable (1) from the system board. CAUTION: There is a ground loop off the display panel cable that is secured to the left hinge. Be sure you do not pull or damage the cable. • The rubber screw covers are available in the Rubber Kit, spare part numbers 497622-001 (for use only with HP Compaq 6535s Notebook PC models) and 491654-001 (for use only with HP Compaq 6530s and 6531s Notebook PC models). The webcam module can be ordered by using spare part numbers 491630-001 (for use only with HP Compaq 6530s and 6531s Notebook PC models) and 493171-001 (for use only with HP Compaq 6535s Notebook PC models). • Disconnect the display panel cable (2) and the backlight cable (3) from the display inverter. Remove the display inverter.